Showing 1470–1480 of 2712 results

These T1, RJ45-RJ45 ( RJ48C ) cross-over Ethernet cables are constructed with premium Quabbin 9720, T1 certified cable. Two individually shielded, 22 AWG, 100 ohm pairs maximize the performance of your expensive T1 circuits and equipment. Beware of generic T1 Ethernet cables made with inexpensive Cat5 unshielded Ethernet cable. The American National Standards Institute (ANSI) states in ANSI T1.403 that T1 cable be constructed of two balanced pairs, 22 AWG Solid conductor, 100 ohm impedance, with a loss budget of 5.5 db. Cross-over wiring configuration available in 3-foot (0.9-meter), 5-foot (1.5-meter), 7-foot (2.1-meter) and 10-foot (3.1-meter) lengths. Custom lengths available. Consult your reseller. Also available in straight-through wiring configuration. See N265-Series T1 Ethernet cables.

1 m. (3 ft.) Green 30Awg SFP+ High Speed Passive Copper 10Gbps CableFully compliant to MSA SFF-8431 specificationEquivalent to Cisco SFP-H10GB-CU1M (See the Support tab on this web page for additional cross references)Use in 10Gbps Ethernet and Fibre Channel applications100ohm Twinaxial cable, Diecast metal shells, pull-to-release latchingSupport for 1x, 2x, 4x and 8x Fiber Channel data ratesHot-Pluggable SFP 20PIN footprintLow power consumption

5M (16.4-ft.) Black 24Awg SFP+ High Speed Passive Copper 10Gbps CableFully compliant to MSA SFF-8431 specificationEquivalent to Cisco SFP-H10GB-CU5M (See the Support tab on this web page for additional cross references)Use in 10Gbps Ethernet and Fibre Channel applications100ohm Twinaxial cable, Diecast metal shells, pull-to-release latchingSupport for 1x, 2x, 4x and 8x Fiber Channel data ratesHot-Pluggable SFP 20PIN footprintLow power consumption

20-in. (50.8 cm) 30 AWG SFP+ high-speed passive copper cable is fully compliant to MSA SFF-8431 specificationSupports 1x, 2x, 4x and 8x Fiber Channel data ratesLow-power equivalence to Cisco SFP-H10GB-CU1-5MIdeal for 10G Ethernet and Fibre Channel applications100-ohm twinaxial cable with die-cast metal shells and pull-tab latches

Connect Network Equipment at Speeds Up to 100 GbpsCombines four 28 Gbps SFP channels into single high-density cableIdeal for data centers, high-end servers and enterprise wiring closetsMulti-platform support for 128G Fibre Channel and EDR InfiniBandLower port cost and power budget when compared to fiber opticsTop-of-the-Line Construction100 GbE 38-position “board-as-connector” designZinc die-cast male QSFP+ connectors for superior EMI resistanceErgonomic pull-tab ejectors for quick, easy connections8-pair wire technology optimized for bandwidth-intense applicationsFlexible 26 AWG conductors maintain smooth high-frequency responseFully Compliant and CompatibleMeets or exceeds strict 100-Gigabit Ethernet (100GBASE-CR4) standardsComplies with IEEE 802.3bj and RoHSComplies with latest QSFP28 MSA (Multi-Source Agreement) SFF-8665 architectureCompatible with all QSFP and QSRP+ portsCompatible to Cisco QSFP-100G-CU3M

"0.5M (20-in.) QSFP+ tp QSFP+ 40Gb Passive DAC Copper Infiniband cableMeets or Exceeds strict 40-Gigabit Ethernet 40GBase-CR4 standardsSDR, DDR, and QDR CompatibleQSFP+ to QSFP+ 30AWG SFF-8436 compliant cable and connectorUp to 10.3125 Gbps transfer rate per channel ( 40Gb aggregate )Multi-platform support for 40Gb, SAS, Fibre Channel, and SONETZinc die-cast QSFP+ connectors with ""Pull-to-Release"" latchingFully compliant to latest QSFP+ MSA ( Multi Source Agreement )Lower port cost and reduced power budget vs Fiber OpticsRoHS, SFF-8436, and IEEE 802.3ba CompliantBER better than 10¹²"

This multimode duplex fiber optic ST/ST Ethernet cable is manufactured from 62.5/125 zipcord fiber. The cable has ST connectors on each end, a PVC jacket and is FDDI and OFNR rated. Duplex multimode fiber is most commonly used in LAN applications.

"Tripp Lite N302-50M. Cable length: 1968.5"" (50 m), Cable type: OFNR, Connector 1: ST, Connector 2: ST, Core diameter: 62.5 µm, Full duplex"

Manufactured from 62.5/125 duplex (zipcord) fiberPVC jacketLength: 1-meter/Connectors: MTRJ to (2) LCInsertion loss testing performed on every connector (0.2db typical) and provided with cableBeveled edge on ends of glass makes insertion of plug a breezeFiber made from glass (not a polymer)Duplex multimode fiber is most commonly used in LAN applications where links are 10-ft. (3.05 m) or lessFiber optic distributed data interface (FDDI) ratedOFNR (riser rated)

Manufactured from 62.5/125 duplex (zipcord) fiberPVC jacketLength: 2-meter/connectors: MTRJ to (2) LCInsertion loss testing performed on every connector (0.2db typical) and provided with cableBeveled edge on ends of glass makes insertion of plug a breezeFiber made from glass (not a polymer)Duplex multimode fiber is most commonly used in LAN applications where links are 10-ft. (3.05 m) or lessFiber optic distributed data interface (FDDI) ratedOFNR (riser rated)