Showing 260–270 of 504 results

Constructed with 50/125 micron cableLength - 10MUse on fiber and fibre channel installationsLC male to LC male connectorsHigher bandwidth optimized for gigabit and 10Gbps networksBackward compatible with 62.5 micron fiberBuilt-in headroom for future applicationsNumber of fibers: 2Fiber type: all glass graded indexCore diameter: Two 50+/-3 micronsCLAD diameter: 125+/-2 micronsPrimary coating diameter: 245+/-15 micronsPrimary coating material: acrylateSecondary coating diameter: 900+/-50 micronsSecondary coating material: PVCAttenuation @850NM: 3.5DB/KM maximum, @1300NM: 1.0DB/KM maximumBandwidth @850NM: 220 MHz-KM minimum, @1300NM: 600 MHz-KM minimumNumeric aperture: .275 nominalProof test level: 100,000 PSIInsertion loss testing performed on every connector (0.2db typical) and provided with cableBeveled edge on ends of glass makes insertion of plug a breeze

Bulk 62.5/125 Multimode Duplex Fiber Optic CableLow-Smoke, Zero Halogen jacketZip-Cord StyleCable marked every meterTemp Range: -20C to +70CSuitable for Indoor Use7lb Reel

2M (6.56-ft.) SC/SC 10Gig, OM3 RatedUse with VCSEL and LED laser light sourcesHigh-Speed, High-Bandwidth, Low-CostBackward compatible with legacy LAN'sIdeal for Fibre Channel (SAN) applicationsIEEE 802.3ae and TIA LOMMF compliant10gb Ethernet speed to 300 meters @850nm

"OM3 Laser-Optimized Multimode Fiber (LOMMF) ""Aqua"" cables are for use with 10 Gb Ethernet applications. These 50/125um LC/LC Fiber Optic cables provide nearly four times the bandwidth over conventional 62.5um multimode fiber with performance rivaling that of singlemode cabling at a much reduced cost. LOMMF cable allows 10 Gb serial transmission over extended distances in the 850 nm wavelength window, where low-cost Vertical Cavity Surface Emitting Lasers (VCSELs) enable a cost-effective, high-bandwidth solution. LOMMF is ideally suited for LANs, SANs and high-speed parallel interconnects for head-ends, central offices and data centers."

MTP / MPO to 8 x LC, 3 Meter Fan-out Cable40GbE rated OM3 50/125 MultimodePlenum rated jacket

MTP / MPO Push-Pull Connectors for Quick Fiber Optic connectionsPush/Pull tab connectors offer maximum accessibility in high density installations; install / remove with one hand12 times the density of SC style connectorsHigh Density design cuts down on installation costs50/125 OM3 Rated Multimode Fiber, 850nmPlenum rated jacketUnique cable ID label for Quality Control and TraceabilityEach cable 100% tested for low insertion loss and back reflectionTest data supplied with each cableCustom lengths available

"1 Meter QSFP+ tp QSFP+ 40Gb Passive DAC Copper Infiniband cableMeets or Exceeds strict 40-Gigabit Ethernet 40GBase-CR4 standardsCompatible to Cisco QSFP-H40G-CU1MSDR, DDR, and QDR CompatibleQSFP+ to QSFP+ 30AWG SFF-8436 compliant cable and connectorUp to 10.3125 Gbps transfer rate per channel ( 40Gb aggregate )Multi-platform support for 40Gb, SAS, Fibre Channel, and SONETZinc die-cast QSFP+ connectors with ""Pull-to-Release"" latchingFully compliant to latest QSFP+ MSA ( Multi Source Agreement )Lower port cost and reduced power budget vs Fiber OpticsRoHS, SFF-8436, and IEEE 802.3ba CompliantBER better than 10¹²"

This multimode duplex fiber optic ST/ST Ethernet cable is manufactured from 62.5/125 zipcord fiber. The cable has ST connectors on each end, a PVC jacket and is FDDI and OFNR rated. Duplex multimode fiber is most commonly used in LAN applications.

Manufactured from 62.5/125 duplex (zipcord) fiberPVC jacketLength: 4-meter connectors: 2 SC/LC connectors on each endInsertion loss testing performed on every connector (0.2db typical) and provided with cableFiber made from glass (not a polymer)Fiber optic distributed data interface (FDDI) rated

Manufactured from 62.5/125 duplex (zipcord) fiberPVC jacketLength: 5-meter connectors: 2 SC/LC connectors on each endInsertion loss testing performed on every connector (0.2db typical) and provided with cableFiber made from glass (not a polymer)Fiber optic distributed data interface (FDDI) rated