Showing 180–190 of 205 results

2-port transmitter and dual receivers extend an HDMI signal via Cat5e/6/6a cable to 2 projectors, monitors or TVs up to 100 ft. away. Recommended for digital signs, classrooms, churches, offices and retail settings.- Built-in Power over Cable (PoC) technology powers the receiver- Supports high-definition video resolutions up to 1080p (@ 60 Hz)- Supports 7.1-channel surround sound audio- HDCP and 3D compliant- Plug and play—no software or drivers to installThe B126-2P2M-POC 2-Port HDMI over Cat5/Cat6 Extender Kit includes a two-port transmitter and two low-profile receivers that work in tandem to extend an HDMI audio/video signal to two projectors, monitors or televisions. The kit is recommended for digital signs, trade shows, classrooms, churches, offices, retail settings and other applications where the source is located farther than conventional cables allow. HDMI cable (see Tripp Lite’s P568-Series) connects the audio/video source, such as a Blu-ray™ player, to the transmitter’s HDMI port. Cat5e/6/6a cable connects the transmitter to the receivers’ RJ45 ports (for best results, use 24 AWG solid-wire Cat6 cable, such as Tripp Lite’s N202-Series). The receivers plug directly into the displays’ HDMI input ports. Built-in PoC technology powers the receivers over Cat5e/6/6a cable, so no external power supply on the display side is needed.The B126-2P2M-POC can extend a high-definition 1080p (at 60 Hz) signal up to 50 feet and a 1080i signal up to 100 feet. In addition to crystal-clear video, the B126-2P2M-POC delivers full, rich audio up to 7.1-channel surround sound (multi-channel or PCM) and supports 3D and HDCP standards. Easy to set up with no software or drivers to install. Transmitter mounts to a wall, rack or pole using the included hardware. Complies with the Federal Trade Agreements Act (TAA) for GSA Schedule purchases.Splits and Extends High-Definition HDMI Audio/Video Signals- 2-port transmitter extends HDMI A/V signal to 2 low-profile receivers- Recommended for digital signs, trade shows, classrooms, churches, offices, retail settings and other HDMI A/V applications- Extends a 1080p (@ 60 Hz) signal up to 50 ft. from source- Extends a 1080i signal up to 100 ft. from source- Supports 7.1-channel surround sound (multi-channel or PCM) audio- HDCP and 3D compliantEasy to Set Up and Use- Plug-and-play engineering—no software or drivers to download and install- Transmitter connects to source using HDMI cable, such as Tripp Lite’s P568-Series- Transmitter and receivers connect with Cat5e/6/6a cable (for best results, use Tripp Lite’s N202-Series)- LEDs indicate when units are receiving power or an HDMI signal- Mounting hardware included for installing transmitter on a wall, rack or poleTAA-CompliantComplies with the Federal Trade Agreements Act (TAA) for GSA Schedule purchases

HDMI to VGA and Audio Converter Splits an HDMI Signal to 2 VGA Displays at the Same TimeThis six-inch adapter cable instantly connects your computer, laptop, notebook, media player, MacBook, Chromebook, Ultrabook, Blu-ray player or other device with an HDMI port to two VGA monitors or projectors simultaneously. It features a male HDMI connector and two female VGA connectors, so you can continue using your existing VGA displays and cables without the expense of new HDMI monitors.Supports High-Definition 1080p and Stereo Audio for Video PresentationsThis HDMI to VGA and audio adapter is ideal for giving video presentations in conference rooms and classrooms or playing video for digital signage in crystal-clear 1080p. It supports video resolutions up to 1920 x 1080, as well as HDCP, EDID and 3D. The HDMI audio signal passes through the adapter and splits to two 3.5 mm stereo jacks. LEDs next to each output port indicate at a glance when the adapter is transmitting a signal to the connected VGA displays.Latching HDMI Plug Provides a Secure ConnectionThe molded HDMI connector features special latches, which help prevent the adapter from becoming loose or accidentally dislodged from the source device and causing signal loss.Plug-and-Play Operation Lets You Begin Watching Video Almost ImmediatelyNo software or drivers are required. The included USB Micro-B cable powers the adapter from a USB port on your HDMI source. The lightweight unit is easy to carry in a pocket, purse, backpack or laptop bag for instant 1080p video where needed.TAA-Compliant for GSA Schedule PurchasesThe P131-06N-2VA-U is compliant with the Federal Trade Agreements Act (TAA), which makes it eligible for GSA (General Services Administration) Schedule and other federal procurement contracts.

The B160-101-HDSI HDMI over IP Gigabit LAN Ethernet Extender Kit extends and distributes HDMI or DVI audio/video, RS-232 serial and IR (infrared) remote signals from the source to the display located up to 328 feet (100 meters) away, which is more than 200 feet (61 meters) farther than a traditional Cat5e/6 solution. By adding a chain of low-cost unmanaged network switches, such as the NG5, you can continue extending the distance between source and display up to 328 feet per switch.Create a multi-in, multi-out installation with up to 64 transmitters and 255 receivers* by including dedicated managed Ethernet network switches** with Internet Group Management Protocol (IGMP), such as the NSS-G16D2. With a compatible B160-Series receiver, you can send the HDMI or DVI video source (a DVI adapter cable is included) to any analog or digital display, including VGA and DisplayPort, allowing you to mix and match technologies and use existing monitors. The IGMP-enabled switch will let you manage all connections for centralized control over which sources show on which displays.The B160-101-HDSI supports video resolutions up to 1920 x 1080 (1080p) at 60 Hz in a point-to-multipoint switch installation. It extends IR control signals that control a source, such as a media server, to a remote display, as well as RS-232 signals at serial baud rates up to 57600 Bps. The transmitter and receiver units mount to a wall, rack or pole using the including hardware.*Unmanaged switch installations are limited to two transmitter units. Number of receivers is limited to number of ports remaining on unmanaged switch.**B160-Series designed for use with dedicated network switch. Connecting to a switch used with other networking equipment will result in degraded or non-functional performance.

HDMI/DVI A/V, Serial and IR Control Signals over Cat5/6 CablingReceives IP-based audio/video transmitted point-to-point from a source 328 ft. away Add low-cost network switches between transmitter and receiver to continue extending distance up to 328 ft. per switchCreate a Multi-In, Multi-Out Installation Using B160-Series Transmitters and ReceiversConnect up to 64 transmitters and 255 receivers through multiple dedicated managed network switchesIGMP-enabled switches allow centralized control over which sources show on which displaysDisplays video from any analog or digital source, so you can mix and match technologies and use existing sources and monitorsEnhanced Technical FeaturesSupports video resolutions up to 1920 x 1080 (1080p) @ 60 HzUses H.264 video compression standardTransmits on 20–60 kHz IR frequencyExtends IR control signals that control a source from a remote displaySupports RS-232 serial baud rates up to 57600 BpsHDCP and 3D compatible when used with a DisplayPort or HDMI transmitter Plug-and-Play FunctionalityNo software or drivers requiredHardware included for mounting on wall, rack or poleCompatible with all B160-Series A/V over IP transmittersTAA-CompliantCompliant with the Federal Trade Agreements Act (TAA) for GSA Schedule purchases

Distributes HDMI/DVI A/V, Serial and IR Control Signals over Cat5/6 CablingConverts audio/video to an IP-based signal that is transmitted point-to-point to a display 328 ft. awayAdd low-cost network switches between transmitter and receiver to continue extending distance up to 328 ft. per switchHDMI output for connecting a local displayCreate a Multi-In, Multi-Out Installation Using B160-Series Transmitters and ReceiversConnect up to 64 transmitters and 255 receivers through multiple dedicated managed network switchesIGMP-enabled switches allow centralized control over which sources show on which displaysVideo source can be sent to any analog or digital display, so you can mix and match technologies and use existing monitorsEnhanced Technical FeaturesSupports video resolutions up to 1920 x 1080 (1080p)Uses H.264 video compression standardTransmits on 20–60 kHz IR frequencyExtends IR control signals that control a source from a remote displaySupports RS-232 serial baud rates up to 57600 BpsHDCP and 3D compatible when used with a DisplayPort or HDMI receiverPlug-and-Play FunctionalityNo software or drivers requiredHardware included for mounting on wall, rack or poleCompatible with all B160-Series A/V over IP receiversTAA-CompliantCompliant with the Federal Trade Agreements Act (TAA) for GSA Schedule purchases

The B055-001-USB-VA NetDirector® USB Server Interface Unit connects a server or computer with HD15 VGA video, 3.5 mm audio and USB mouse/keyboard ports to a compatible B064-IPG Series KVM switch. Using Cat5e/6 cabling, you can locate the KVM switch up to 164 feet (50 meters) from the server.Allowing the server to access the KVM switch’s Virtual Media functionality via low-cost Cat5e/6 cable eliminates the need for bulky KVM cables. This frees up precious space in your server cabinet, and allows for better ventilation and longer cable runs. Running cable through conduit and other tight spaces takes advantage of the increased flexibility when setting up your network application.No software or external power supply is needed. The unit’s compact, lightweight design is plug-and-play for immediate installation and deployment. It complies with the Federal Trade Agreements Act (TAA) for GSA Schedule purchases.Note: SIUs that were purchased prior to that of your KVM switch may require a firmware upgrade in order for them to work properly (see Maintenance under OSD Operation section of your B064-Series KVM Owner's Manual for details)

Distributes DisplayPort A/V, Serial and IR Control Signals over Cat5/6 CablingConverts audio/video to an IP-based signal that is transmitted point-to-point to a display 328 ft. awayAdd low-cost network switches between transmitter and receiver to continue extending distance up to 328 ft. per switchHDMI output for connecting a local displayCreate a Multi-In, Multi-Out Installation Using B160-Series Transmitters and ReceiversConnect up to 64 transmitters and 255 receivers through multiple dedicated managed network switchesIGMP-enabled switches allow centralized control over which sources show on which displaysVideo source can be sent to any analog or digital display, so you can mix and match technologies and use existing monitorsEnhanced Technical FeaturesSupports video resolutions up to 1920 x 1080, including 1080p (limited to receiver’s max resolution)Uses H.264 video compression standardTransmits on 20–60 kHz IR frequencyExtends IR control signals that control a source from a remote displaySupports RS-232 serial baud rates up to 57600 BpsHDCP and 3D compatible when used with a DisplayPort or HDMI receiver (not compatible with VGA receiver)Plug-and-Play FunctionalityNo software or drivers requiredHardware included for mounting on wall, rack or poleCompatible with all B160-Series A/V over IP receiversTAA-CompliantCompliant with the Federal Trade Agreements Act (TAA) for GSA Schedule purchases

The BHDBT-K-E3SI-LR HDBaseT HDMI over Cat5e/6/6a Extender Kit extends uncompressed HDMI audio and video, RS-232 serial and IR remote control signals up to 99.97 m (328-ft.) over a single Cat5e/6/6a cable, including an Ultra High Definition (UHD) 3840 x 2160 (4K x 2K) signal. In addition to HDMI, RS-232 and IR signals, this extender kit features three built-in 10/100 Ethernet ports on both the transmitter and receiver units. This allows connected devices, such as a Blu-ray™ player, cable/satellite box, and HDMI television, to communicate with each other and access online content via LAN. You can also control RS-232 serial devices, such as touchscreen displays or scanners, at baud rates up to 115 Kbps. The two-way IR remote control feature (@ 39 KHz) lets you control your Blu-ray player using its remote when at the remote monitor or control your remote monitor using its remote when at the Blu-ray player. Locking HDMI ports (ideal for use with Tripp Lite’s P569-006-LOCK high-speed HDMI cables with locking connectors) on both the transmitter and receiver prevent cables from coming loose or undone, ensuring an intact signal. The plug-and-play BHDBT-K-E3SI-LR supports 7.1-channel surround sound, DTS-HD and Dolby TrueHD audio, as well as 3D video, EDID and HDCP.- Ideal for digital signs, classrooms and trade show booths- Built-in 10/100 Ethernet ports on transmitter and receiver- Extends a 3840 x 2160 (4K x 2K) signal up to 99.97 m (328 ft.)- Supports 7.1-channel surround sound, DTS-HD and Dolby TrueHD- Controls RS-232 serial devices at baud rates up to 115 Kbps- Ideal for digital signage, classrooms, retail locations, conference rooms and trade show booths- Extends an Ultra High Definition (UHD) 3840 x 2160 (4K x 2K) signal up to 99.97 m (328 ft.)- Supports 7.1-channel surround sound, DTS-HD and Dolby TrueHD audio- Supports 3D video, EDID and HDCP- Reduces cable clutter and installation costs- Allows connected devices to communicate with each other and access online content via LAN- 2-way 39 KHz IR remote control functionality lets you control your Blu-ray player with its remote while standing at the remote monitor (and vice versa)- RS-232 serial port supports 115 Kbps full-duplex baud rates for scanners and touchscreen monitors- Plug and play with no software or drivers to download and install- Included mounting hardware for installing each unit on a wall, rack or pole- Prevent cables from coming loose or disconnected, ensuring an intact signal

The B155-002-DP-V2 2-Port Mini DisplayPort 1.2 to DisplayPort MST Hub connects two DisplayPort monitors to the Mini DisplayPort output on your computer. Ideal for digital signage in schools, churches, conference rooms, trade shows, hotels and retail outlets, this hub allows you to display the same image on both monitors, extend the desktop across them, or combine both into one large monitor in video wall mode.The B155-002-DP-V2 is compliant with DisplayPort 1.2 and backward compatible with versions 1.1 and 1.1a with the feature set being limited to that of your equipment. It supports Ultra High Definition (UHD) video resolutions up to 4K @ 60Hz (3840 x 2160). This MST hub also supports HDCP, EDID, DDC and 48-bit Deep Color (16 bits per channel), as well as DTS-HD, Dolby TrueHD and 7.1-channel surround sound audio.The B155-002-DP-V2 works with all operating systems. Plug-and-play convenience means no software, drivers or external power supply is needed. The included three-foot USB Micro-B cable delivers necessary power from the connected computer. A built-in six-inch cable connects directly to a Mini DisplayPort source. LEDs indicate when the monitors are receiving a signal. The B155-002-DP-V2 complies with the Federal Trade Agreements Act (TAA) for GSA Schedule purchases.Connects 2 DisplayPort Monitors to Your Computer’s Mini DisplayPortIdeal for digital signs in schools, churches, conference rooms, trade shows and retail settingsDisplays same image on 2 monitors simultaneously in mirror modeExtends desktop across 2 monitors in extended modeCombines 2 monitors into one large monitor in video wall modeBuilt-in 6 in. cable connects directly to Mini DisplayPort sourceLEDs indicate when monitors are receiving a signalMeets the Latest Performance StandardsSupports UHD video resolutions up to 4K @ 60Hz (3840 x 2160)Supports HDCP, EDID and DDCSupports 48-bit Deep Color (16 bits per channel)Supports DTS-HD, Dolby TrueHD and 7.1-channel surround sound audioBackward compatible with DisplayPort 1.1 and 1.1aEasy to Use Almost AnywhereWorks with all operating systemsPlug and play—no software, drivers or external power supply requiredBus-powered via included USB Micro-B cableTAA CompliantComplies with Federal Trade Agreements Act (TAA) for GSA Schedule purchases

The B126-2X2 2-port HDMI over Cat5/Cat6 Matrix Splitter Switch works with Tripp Lite remote receivers to share one or more HDMI sources between multiple projectors, monitors or televisions. It’s ideal for digital signs, trade shows, presentations, retail and other applications where the video sources are located farther than conventional cables allow or that require multiple displays connected to one source. It uses HDMI cable (see Tripp Lite’s P568-Series) to connect to the sources and Cat5e/6 cable to transmit to the remote monitors (for best results, use 24 AWG solid-wire Cat5e/6 cable, such as Tripp Lite’s N202-Series). Any video source can be routed to any monitor, or you can send the same source to multiple monitors. Switch between inputs via pushbuttons, RS-232 serial or the included remote control. When used with Tripp Lite’s B126-1A0 or B126-1A0-WP-1 active remote receivers, the switch can extend a 1080i (60 Hz) signal up to 53.34 m (175-ft.) or a 1080p signal (60 Hz) up to 38.1 m (125-ft.). With a B126-1P0 or B126-1P0-WP-1 passive remote receiver, it can extend a 1080i (60 Hz) signal up to 22.86 m (75-ft.) and a 1080p (60 Hz) signal up to 15.24 m (50-ft.) Add up to three B126-110 remote repeaters to each channel to fully extend the signal range or add more displays. In addition to crystal-clear video, the B126-2X2 delivers full, rich stereo. Easy to set up with no software or drivers to install. Mounts to a wall, rack or pole using the included hardware.- Routes any source to any display or same source to multiple displays- Supports high-definition video resolutions up to 1080p (60 Hz)- Switches inputs via button, remote control or RS-232 serial- Works with all operating systems and HDMI video sources- Plug and play—no software or drivers to install- Extends a 1080i (60 Hz) signal up to 53.34 m (175-ft.) and a 1080p (60 Hz) signal up to 38.1 m (125 ft.) with each optional B126-110 remote repeater - Extends a 1080i (60 Hz) signal up to 53.34 m (175-ft.) and a 1080p (60 Hz) signal up to 38.1 m (125 ft.) with B126-1A0 or B126-1A0-WP-1 active remote receiver- Extends a 1080i (60 Hz) signal up to 22.86 m (75-ft.) and a 1080p (60 Hz) signal up to 15.24 m (50 ft.) with B126-1P0 or B126-1P0-WP-1 passive remote receiver- Add up to 3 remote repeaters on each channel for maximum signal range - Connects to next link in the chain with one Cat5e/6 cable (for best results, use 24 AWG solid-wire Cat5e/6 cable, such as Tripp Lite’s N202-Series)- Supports the Latest Video and Audio Resolutions - Works with all operating systems and HDMI video sources - Supports HD resolutions up to 1080p (60 Hz)- Supports stereo audio - Supports 24-bit True Color (8 bits per channel) and HDCP- Route any video display to any monitor, or route the same display to multiple monitors- Plug-and-play engineering—no software or drivers to download and install- Connects quickly to sources with HDMI cable, such as Tripp Lite’s P568-Series- LEDs indicate at a glance when the unit is receiving power and an HDMI signal from the source - Included mounting hardware lets you install the units on a wall, rack or pole- International AC Adapter B110-INT required for use with UK, European, and Australian power connections