Showing 620–630 of 2256 results

The B126-1A0-WP-1 HDMI over Cat5/Cat6 Active Remote Receiver works with Tripp Lite’s B126-002 or B126-004 transmitter to extend an HDMI signal to a projector, monitor or television. It’s ideal for digital signs, trade shows, presentations, classrooms, churches, retail settings and other applications where the video source is located farther than conventional cables allow or that require multiple displays connected to one source. The receiver uses HDMI cable (see Tripp Lite’s P568-Series) to connect to the monitor and Cat5e/6 cable to receive the signal from the transmitter or a remote repeater in the chain (for best results, use 24 AWG solid-wire Cat5e/6 cable, such as Tripp Lite’s N202-Series). No 110 punchdown connection is required.The B126-1A0-WP-1 can extend a 1080i (60 Hz) signal up to 61 m (200-ft.), a 1080p (60 Hz) signal up to 46 m (150-ft.) and a 3D signal up to 38 m (125-ft.) You can connect up to three B126-110 remote repeaters in the chain for a total of four HDMI displays and full signal extension of 213 m (700-ft.) (1080i), 152 m (500-ft.) (1080p) or 122 m (400-ft.) (3D).In addition to crystal-clear video, the B126-1A0-WP-1 delivers full, rich stereo and 7.1-channel surround sound (multi-channel or PCM) audio when paired with a B126-002 or B126-004 transmitter. Built-in equalization control lets you fine-tune the image quality at each remote display. Supports 24-bit True Color (8 bits per channel) and HDCP compatibility. Easy to set up with no software or drivers to install. Mounts to a wall using the included hardware. - Supports high-definition video resolutions up to 1080p (60 Hz) - Supports stereo and 7.1-channel surround sound audio - Works with all operating systems and HDMI video sources - Plug and play—no software or drivers to install - Built-in equalization control lets you adjust monitor imageSystem Requirements - For international use, the B110-INT power supply canbe purchased separately; it features plugs for the UK, Europe, and Australia - B126-1A0-WP-1 HDMI over Cat5/Cat6 Active Remote Receiver - Screwdriver for adjusting equalization - External Power Supply with NEMA 1-15P Plug(Input: 100–240V, 50/60 Hz, 0.5A; Output: 5V, 2A, 1.52 m (5-ft.) - Mounting hardware - Owner’s Manual - Works in tandem with Tripp Lite’s B126-002 or B126-004 transmitter unit - Extends a 1080i (60 Hz) signal up to 61 m (200-ft.), a 1080p (60 Hz) signal up to 46 m (150-ft.) and a 3D signal up to 38 m (125-ft.) - Connect up to 3 B126-110 remote repeaters to the chain for maximum signal range of 213 m (700-ft.) (1080i), 152 m (500-ft.) (1080p) and 122 m (400-ft.) (3D) - Connects to previous link in the chain with one Cat5e/6 cable (for best results, use 24 AWG solid-wire Cat5e/6 cable, such as Tripp Lite’s N202-Series) - No 110 punchdown connection requiredSupports the Latest Video and Audio Resolutions - Works with all operating systems and HDMI video sources - Supports HD resolutions up to 1080p (60 Hz) - Supports stereo and 7.1-channel surround sound (multi-channel or PCM) audio when paired with a B126-002 or B126-004 transmitter - Supports 24-bit True Color (8 bits per channel) and HDCP - Built-in equalization control lets you adjust the image on the local monitorEasy to Set Up and Use - Plug-and-play engineering—no software or drivers to download and install - Connects quickly to local monitor with HDMI cable, such as Tripp Lite’s P568-Series - LEDs indicate at a glance when the unit is receiving power and a signal from the previous link in the chain - Included mounting hardware lets you install the unit on a wall

The B126-1A1-POC HDMI over Cat5 Active Extender Kit includes a transmitter unit and a receiver unit that work in tandem to extend an HDMI audio/video signal to a projector, monitor or television. The kit is ideal for digital signs, trade shows, classrooms, churches, offices, retail settings and other applications where the source is located farther than conventional cables allow. HDMI cable (see Tripp Lite’s P569-Series) connects an optional local display and the audio/video source, such as a Blu-ray™ player, to the transmitter’s HDMI ports and a remote display to the receiver. Cat5e/6/6a cable connects the two units (for best results, use 24 AWG solid-wire Cat5e/6 cable, such as Tripp Lite’s N202-Series). Built-in Power over Cable (POC) technology powers the receiver over Cat5e/6/6a cable, so no external power supply on the display side is needed.The B126-1A1-POC can extend a high-definition 1080p (@ 60 Hz) signal up to 125 feet. In addition to crystal-clear video, the B126-1A1-POC delivers full, rich stereo and 7.1-channel surround sound (multi-channel or PCM). Built-in equalization control lets you fine-tune the image quality at the remote display. Supports 24-bit True Color (8 bits per channel) and HDCP. Easy to set up with no software or drivers to install. Mounts to a wall, rack or pole using the included hardware. Complies with the Federal Trade Agreements Act (TAA) for GSA Schedule purchases.Extends High-Definition Signals- Extends a 1080p (@ 60 Hz) signal up to 125 ft.- Transmitter and receiver connect with one Cat5e/6/6a cable (for best results, use 24 AWG solid-wire Cat5e/6 cable, such as Tripp Lite’s N202-Series)- Supports stereo and 7.1-channel surround sound (multi-channel or PCM) audio- Supports 24-bit True Color (8 bits per channel) and HDCP- Built-in equalization control lets you adjust the image on the local monitorEasy to Set Up and Use- Plug-and-play engineering—no software or drivers to download and install- Works with all operating systems and HDMI video sources- Units connect quickly to monitors with HDMI cable, such as Tripp Lite’s P569-Series- LEDs indicate at a glance when the units are receiving power and an HDMI signal- Included mounting hardware lets you install the units on a wall, rack or poleTAA Compliant- Complies with the Federal Trade Agreements Act (TAA) for GSA Schedule purchases

The B126-2A0 HDMI over Cat5/Cat6 Active Remote Receiver works with Tripp Lite’s B126-002 or B126-004 transmitter to extend an HDMI signal and split it to two projectors, monitors or televisions. It’s ideal for digital signs, trade shows, presentations, classrooms, churches, retail settings and other applications where the video source is located farther than conventional cables allow or that require multiple displays connected to one source. The receiver uses HDMI cable (see Tripp Lite’s P568-Series) to connect to the monitors and Cat5e/6 cable to receive the signal from the transmitter or a remote repeater in the chain (for best results, use 24 AWG solid-wire Cat5e/6 cable, such as Tripp Lite’s N202-Series).The B126-2A0 can extend a 1080i (60 Hz) signal up to 60.96 m (200-ft.), a 1080p (60 Hz) signal up to 45.72 m (150-ft.) and a 3D signal up to 38.1 m (125-ft.) You can connect up to three B126-110 remote repeaters in the chain for a maximum of six HDMI displays and full signal extension of 213.36 m (700-ft.) (1080i), 152.4 m (500-ft.) (1080p) or 121.9 m (400-ft.) (3D).In addition to crystal-clear video, the B126-2A0 delivers full, rich stereo and 7.1-channel surround sound (multi-channel or PCM) audio when paired with a B126-002 or B126-004 transmitter. Built-in equalization control lets you fine-tune the image quality at each remote display. Supports 24-bit True Color (8 bits per channel) and HDCP compatibility. Easy to set up with no software or drivers to install. Mounts to a wall, rack or pole using the included hardware.- Supports high-definition video resolutions up to 1080p (60 Hz)- Supports stereo and 7.1-channel surround sound audio- Works with all operating systems and HDMI video sources- Plug and play—no software or drivers to install- Built-in equalization control lets you adjust monitor image- Works in tandem with Tripp Lite’s B126-002 or B126-004 transmitter unit- Extends a 1080i (60 Hz) signal up to 200 ft., a 1080p (60 Hz) signal up to 45.72 m (150-ft.) and a 3D signal up to 38.1 m (125-ft.) - Connect up to 3 B126-110 remote repeaters to the chain for maximum signal range of 213.36 m (700-ft.) (1080i), 152.4 m (500 feet) (1080p) and 121.9 m (400 feet) (3D) - Connects to previous link in the chain with one Cat5e/6 cable (for best results, use 24 AWG solid-wire Cat5e/6 cable, such as Tripp Lite’s N202-Series)- Works with all operating systems and HDMI video sources - Supports HD resolutions up to 1080p (60 Hz)- Supports stereo and 7.1-channel surround sound (multi-channel or PCM) audio when paired with a B126-002 or B126-004 transmitter- Supports 24-bit True Color (8 bits per channel) and HDCP - Built-in equalization control lets you adjust the image on the local monitor- Plug-and-play engineering—no software or drivers to download and install - Connects quickly to monitors with HDMI cable, such as Tripp Lite’s P568-Series - LEDs indicate at a glance when the unit is receiving power and a signal from the previous link in the chain- Included mounting hardware lets you install the unit on a wall, rack or pole- International AC Adapter B110-INT required for use with UK, European, and Australian power connections

Optoma ZH400 data projector 4000 ANSI lumens DLP 1080p (1920x1080) 3D White

More Flexibility for Room Design and InstallationCompatible with Vaddio's HDBaseT cameras, this OneLINK kit provides more freedom of choice for camera selection and equipment placement.

The EasyIP AMP D is a half-rack PoE+ powered amplifier featuring Dante networked audio. A single ethernet cable provides power and a Dante audio signal to the EasyIP AMP D and the amplifier’s speaker output provides up to 25 watts of power to a connected speaker.

The C2G 2-Port VGA Auto Switch is perfect for switching between two source devices connected to a single display. For example, in a learning, sharing and collaborating environment, the VGA Auto Switch allows a document camera and a PC to be connected to a single VGA input on the display. The switch may be set so that the PC is displayed until the document camera is powered on causing an automatic switch that will allow the document camera to be displayed. When the document camera is powered off, the switch will then allow the PC to be displayed. The C2G 2-Port VGA Auto Switch has a small footprint allowing it to be placed in a convenient location for manual operation. No software is required for automatic or manual selection modes. The C2G 2-Port VGA Auto Switch features Extended Display Identification Data (EDID) copy, which ensures that the content from the source devices is sent to the display at the optimal resolution.

DisplayPort HDBaseT Extender over Cat Receiver (TAA Compliant)The DisplayPort HDBaseT over Cat Extender allows DisplayPort audio/video signals to be extended over a single Cat5e, Cat6, or Cat6a cable up to 300ft at a 1080p resolution. This receiver requires a DisplayPort or HDMI HDBaseT Transmitter for a complete solution. This solution is compatible with any operating system and is truly plug and play with no drivers or software required. This solution utilizes TruChoice power, which allows power to be supplied over the Cat cable to both the transmitter and receiver from a single power adapter placed at either the transmitter or the receiver end of the solution. HDBaseT technology supports HDCP and allows the Extended Display Identification Data (EDID) signals, i.e. communication of the display’s capabilities, to pass through the extension solution ensuring that the content from the source is sent at the optimal resolution for the display. Built-in power surge protection and high ground loop immunity ensure high performance signal extension.

Kramer Electronics PT-3UC AV transmitter Black

Kramer Electronics EXT3-TR AV transmitter & receiver Black