Showing 100–110 of 184 results

The B140-002 transmits a DVI-D Single-Link signal to two monitors up to 61 m (200-ft.) away using a single Cat5e/6 patch cable. To achieve maximum distance and resolution, use 24Awg Solid Wire Cat5e/6 cable (Tripp Lite's N202-Series). The B140-002 is compatible with all operating systems, and is plug and play, with no software or drivers required. It also comes with mounting hardware that allows it to be wallmounted, rackmounted, or pole-mounted.Installation is simple. Connect the B140-002 transmitter to a DVI source using a Tripp Lite P561-Series DVI cable (not included). Connect a Tripp Lite B140-series receiver (not included) to each display using a Tripp Lite P561-Series DVI cable (not included). Finally, each remote receiver is connected to an RJ45 port on the B140-002 using a single Cat5e/6 cable.For longer extension distances, use a B140-1A0 or B140-1A0-WP active receiver unit to extend a 1920 x 1080 @ 60Hz signal up to 46 m (150-ft.), or a 1024 x 768 @ 60Hz signal up to 61 m (200-ft.)For shorter extension distances, use a B140-1P0 passive receiver unit to extend a 1920 x 1080 @ 60Hz signal up to 15 m (50-ft.), or a 1024 x 768 @ 60Hz signal up to 31 m (100-ft.)Further expand the range and number of monitors by using a B140-110 repeater unit. Add up to four remote units (three repeaters and one active receiver) to each channel of the B140-002, for a total of 4 displays per channel. (An active receiver should be the last unit in a channel) A 1920 x 1080 @ 60Hz signal can be extended up to 38 m (125-ft.) from each repeater to the next unit in the channel, or a 1024 x 768 @ 60Hz signal can be extended up to 53 m (175-ft.) - Supports DVI-D Single-Link video resolutions up to 1920 x 1080 @ 60Hz - For longer distances - Use a B140-1A0 or B140-1A0-WP active receiver unit to extend a 1920 x 1080 @ 60Hz signal up to 46 m (150-ft.), or a 1024 x 768 @ 60Hz signal up to 61 m (200-ft.) - For shorter distances - Use a B140-1P0 or B140-1P0-WP-1 passive receiver unit to extend a 1920 x 1080 @ 60Hz signal up to 15 m (50-ft.), or a 1024 x 768 @ 60Hz signal up to 31 m (100-ft.) - Use 24AWG, Solid Wire Cat5e/6 cable, such as Tripp Lite's N202-Series, to achieve maximum distance and resolution - Can further expand the range and number of monitors by adding B140-110 repeaters - Compatible with all operating systems - Plug and play, no software or drivers requiredSystem RequirementsInternational AC Adapter B110-INT required for use with UK, European, and Australian power connections- B140-002 DVI Over Cat5 Extender/Splitter, 2-Port Local Transmitter Unit - Mounting hardware - External Power Supply with NEMA 1-15P Plug (Input: 100-240V, 50/60Hz, 0.5A; Output: 5V, 2A, 1.52 m (5-ft.) - Owner's Manual - Transmit a DVI-D Single-Link signal to two monitors up to 61 m (200-ft.) away using a single Cat5e/6 patch cable - Supports DVI-D Single-Link video resolutions up to 1920 x 1080 @ 60Hz - For longer distances - Use a B140-1A0 or B140-1A0-WP active receiver unit to extend a 1920 x 1080 @ 60Hz signal up to 46 m (150-ft.), or a 1024 x 768 @ 60Hz signal up to 61 m (200-ft.) - For shorter distances - Use a B140-1P0 or B140-1P0-WP-1 passive receiver unit to extend a 1920 x 1080 @ 60Hz signal up to 15 m (50-ft.), or a 1024 x 768 @ 60Hz signal up to 31 m (100-ft.) - Use 24AWG, Solid Wire Cat5e/6 cable, such as Tripp Lite's N202-Series, to achieve maximum distance and resolution - Further expand the range and number of monitors by using a B140-110 repeater unit - Add up to four remote units (three repeaters and one active receiver) to each channel of the B140-002, for a total of 4 displays per channel. (An active receiver should be the last unit in a channel) - A 1920 x 1080 @ 60Hz signal can be extended up to 38 m (125-ft.) from each repeater to the next unit in the channel, or a 1024 x 768 @ 60Hz signal can be extended up to 53.34 m (175-ft.) - HDCP compatible - Compatible with all operating systems - Plug and play; no software or drivers required - Mounting hardware included

The B140-110 remote repeater unit can be added to your Tripp Lite B140-Series HDMI over Cat5 installation to expand the range and number of monitors. It transmits a DVI-D Single-Link signal up to 53.34 m (175-ft.) away using a single Cat5e/6 patch cable. To achieve maximum distance and resolution, use 24AWG Solid Wire Cat5e/6 cable (Tripp Lite's N202-Series). The B140-110 is compatible with all operating systems, and is plug and play, with no software or drivers required. It features a built-in Equalization control for adjustment of the video image. Installation is simple; just insert the B140-110 repeater into the middle of your installation (Cannot be used with Passive extender kits or Passive receiver units). In the case of a B140-101X active extender kit, the built-in DVI connector on the transmitter is connected to the DVI source. It is then connected via Cat5e/6 cable to the B140-110, which is connected via Cat5e/6 cable to the B140-101X receiver unit. Finally, a monitor is connected to both the repeater and receiver units using Tripp Lite P561-Series DVI cable (not included). Connect up to four remote units (three repeaters and one active receiver) in a single chain, for a total of 4 displays. (An active receiver should be the last unit in a chain) A 1920 x 1080 @ 60Hz signal can be extended up to 38.1 m (125-ft.) from each repeater to the next unit in the channel, or a 1024 x 768 @ 60Hz signal can be extended up to 53.34 m (175-ft.)- Insert into your Tripp Lite B140-Series DVI over Cat5 installation to expand the range and number of monitors (Cannot be used with Passive extender kits or Passive receiver units)- Supports DVI-D Single-Link video resolutions up to 1920 x 1080 @ 60Hz- Extends a 1920 x 1080 @ 60Hz signal up to 38.1 m (125-ft.), or a 1024 x 768 @ 60Hz signal up to 53.34 m (175-ft.)- Use 24AWG, Solid Wire Cat5e/6 cable, such as Tripp Lite's N202-Series, to achieve maximum distance and resolution- Compatible with all operating systems- Plug and play, no software or drivers required- Features a built-in Equalization control for adjustment of the video image- Supports DVI-D Single-Link video resolutions up to 1920 x 1080 @ 60Hz- Extends a 1920 x 1080 @ 60Hz signal up to 38.1 m (125-ft.), or a 1024 x 768 @ 60Hz signal up to 53.34 m (175-ft.) - Insert into your Tripp Lite B140-Series DVI over Cat5 installation to expand the range and number of monitors (Cannot be used with Passive extender kits or Passive receiver units) - Add up to four remote units (three repeaters and one active receiver) in a single chain, for a total of 4 displays. (An active receiver should be the last unit in a chain)- A 1920 x 1080 @ 60Hz signal can be extended up to 38.1 m (125-ft.) from each repeater to the next unit in the chain, or a 1024 x 768 @ 60Hz signal can be extended up to 53.34 m (175-ft.)- Use 24AWG, Solid Wire Cat5e/6 cable, such as Tripp Lite's N202-Series, to achieve maximum distance and resolution- Features a built-in Equalization control for adjustment of the video image - HDCP compatible- Compatible with all operating systems- Plug and play; no software or drivers required- International AC Adapter B110-INT required for use with UK, European, and Australian power connections

Tripp Lite's B140-202, 2X2 DVI Matrix Switch allows two DVI Single-Link video sources to be routed to one or two RJ45 outputs and extended up to 45.72 m (150-ft.) @ 1920x1200 using Active (powered) Receiver, or up to 15.24 m (50-ft.) @ 1920x1200 using Passive (non-powered) Rec. Switching between sources is done manually or with included remote control. Additional monitors can be added beyond the typical two by using Tripp Lite B140-110 daisy-chain Receivers - up to 4 monitors per channel.- Share two DVI sources between two monitors- Supports DVI Single Link computer resolutions up to 1920 x 1200 @ 60Hz - Transmits over inexpensive Cat5e/6 cable up to 60.96 m (200-ft.)- Plug-and-Play- Share two DVI video sources between two monitors- Supports DVI Single Link computer resolutions up to 1920 x 1200 @ 60Hz - Allows either input to be routed to either output, or the one input signal to both outputs - Transmits over a single Cat5e/6 cable to a remote monitor up to 60.96 m (200-ft.) away - HDCP and EDID compliant- Plug-and-Play- A B140-Series remote receiver is needed at each monitor - Active (powered) and Passive (non-powered) Receivers available- Use 24AWG Solid Wire Cat5e/6 patch for maximum video performance - Further expand the range and number of monitors with B140-110 Daisy-Chain Repeaters- International AC Adapter B110-INT required for use with UK, European, and Australian power connections

The B156-004-V2 4-Port DisplayPort 1.2 MST Hub connects up to four DisplayPort monitors to the DisplayPort output on your computer. Ideal for digital signage in schools, churches, conference rooms, trade shows, hotels and retail outlets, this hub allows you to display the same image on all four monitors, extend the desktop across them, or combine all four into one large monitor in video wall mode. The B156-004-V2 is compliant with DisplayPort 1.2 and backward compatible with versions 1.1 and 1.1a with the feature set being limited to that of your equipment. It supports high-definition video resolutions up to 1920 x 1080 (1080p) per monitor. In video wall mode, this hub supports expanded video resolutions, such as 3840 x 2160 (4K x 2K) in a 2 x 2 monitor configuration or 7680 x 1080 in a vertical 4 x 1 configuration. This MST hub also supports HDCP, EDID, DDC and 48-bit Deep Color (16 bits per channel), as well as DTS-HD, Dolby TrueHD and 7.1-channel surround sound audio. It works with all operating systems. Plug-and-play convenience means no software or drivers are needed. A built-in six-inch cable connects directly to a DisplayPort source. LEDs indicate when the monitors are receiving a signal. Connects Up to 4 DisplayPort Monitors to Your Computer’s DisplayPort Output ● Ideal for digital signs in schools, churches, conference rooms, trade shows and retail settings ● Displays same image on 4 monitors simultaneously in mirror mode ● Extends desktop across 4 monitors in extended mode ● Combines 4 monitors into one large monitor in video wall mode ● Built-in 6 in. cable connects directly to DisplayPort source ● LEDs indicate when monitors are receiving a signal Meets the Latest Performance Standards ● Supports HD video resolutions up to 1920 x 1080 per monitor ● Supports expanded resolutions in video wall mode, such as 3840 x 2160 (4K x 2K) in a 2 x 2 monitor configuration or 7680 x 1080 in a vertical 4 x 1 configuration ● Supports HDCP, EDID and DDC ● Supports 48-bit Deep Color (16 bits per channel) ● Supports DTS-HD, Dolby True HD and 7.1-channel surround sound audio ● Backward compatible with DisplayPort 1.1 and 1.1a Easy to Use Almost Anywhere ● Works with all operating systems ● Plug and play—no software or drivers required● Supports UHD video resolutions up to 3840 x 2160 (4K x 2K) ● Built-in 6 in. cable connects directly to DisplayPort source ● Supports up to 48-bit Deep Color (16 bits per channel) ● Works with all operating systems ● Supports DTS-HD, Dolby TrueHD and 7.1-channel surround sound System Requirements● Computer with DisplayPort 1.2-compatible graphics card (e.g. AMD Radeon with AMD Eyefinity) required for video wall mode. ● Backward compatible with most DisplayPort 1.1a equipment running current graphics drivers with feature set limited to that of your equipment. Compatibility with older graphics cards not guaranteed. ● Mac OS X does not support MST for NVIDIA and Intel Graphics Processor Units, limiting video display on connected monitors to mirror mode. ● MST-compliant graphics cards are limited to a bandwidth of 21.6 Gbps amongst all monitors with higher resolution monitors using up more bandwidth. 1080p monitors will use up approximately 22% of bandwidth, whereas 4K monitors will use 40% or more. As each monitor will be different, it is necessary to verify the percentage of bandwidth being used by each monitor in the display settings interface of your graphics card. If the total percentage of bandwidth taken up by all the connected monitors exceeds 100%, an image will not display on one or more of them. ● Monitor(s) with DisplayPort input. Package Includes● B156-004-V2 4-Port DisplayPort 1.2 MST Hub ● External power supply with NEMA 1-15P plug and 1.52 m (5-ft.) cord (Input: 100–240V, 50/60 Hz, 0.5A; Output: 5V, 2A) ● Owner’s manual

The BHDBT-K-PI HDBaseT Class B (HDBaseT-Lite) HDMI over Cat5e/6/6a Extender Kit extends uncompressed HDMI audio and video and IR remote control signals up to 70.1 m (230-ft.) over a single Cat5e/6/6a cable, including video resolutions up to 1920 x 1080 (1080p). It also extends an Ultra High Definition (UHD) 3840 x 2160 (4K x 2K) signal up to 39.62 m (130-ft.) In addition to HDMI and IR signals, this extender kit features built-in PoE technology, which powers the receiver over Cat5e/6/6a cable, eliminating the need for an external power source. The two-way IR remote control feature (@ 39 KHz) lets you control your Blu-ray player or other HDMI source using its remote when at the remote monitor or control your remote monitor using its remote when at the Blu-ray player. Locking HDMI ports (ideal for use with Tripp Lite’s P569-006-LOCK high-speed HDMI cables with locking connectors) on both the transmitter and receiver prevent cables from coming loose or undone, ensuring an intact signal. The plug-and-play BHDBT-K-PI supports 7.1-channel surround sound, DTS-HD and Dolby TrueHD audio, as well as 3D video, EDID and HDCP. Attach the transmitter and receiver units to a wall, rack or pole with the included mounting hardware.- Ideal for digital signs, classrooms and trade show booths- Extends a 3840 x 2160 (4K x 2K) signal up to 39.62 m (130 ft.)- Extends a 1920 x 1080 (1080p) signal up to 70.1 m (230 ft.)- Supports 7.1-channel surround sound, DTS-HD and Dolby TrueHD- Built-in PoE technology powers receiver over Cat5e/6/6a cable- Ideal for digital signage, classrooms, retail locations, conference rooms and trade show booths- Extends an Ultra High Definition (UHD) 3840 x 2160 (4K x 2K) signal up to 39.62 m (130 ft.)- Extends a high-definition 1920 x 1080 (1080p) signal up to 70.1 m (230 ft.)- Supports 7.1-channel surround sound, DTS-HD and Dolby TrueHD audio- Supports 3D video, EDID and HDCP- Reduces cable clutter and installation costs- Built-in PoE technology powers receiver over Cat5e/6/6a cable, eliminating need for external power source- 2-way 39 KHz IR remote control functionality lets you control your Blu-ray player with its remote while standing at the remote monitor (and vice versa)- Prevent cables from coming loose or disconnected, ensuring an intact signal- Ideal for use with Tripp Lite’s P569-006-LOCK high-speed HDMI cables with locking connectors- Plug and play with no software or drivers to download and install- Includes mounting hardware for attaching each unit to a wall, rack or pole

"Tripp Lite B120-000. Type: AV repeater, Maximum resolution: 2560 x 1600 pixels, Maximum transfer distance: 1800"" (45.7 m). AC input voltage: 100-240 V, AC input frequency: 50 - 60 Hz. Width: 2.4"" (61 mm), Depth: 2"" (50.8 mm), Height: 0.949"" (24.1 mm). Package width: 6.4"" (162.6 mm), Package depth: 2.2"" (55.9 mm), Package height: 7"" (177.8 mm). Master (outer) case width: 13.7"" (348 mm), Master (outer) case length: 8.7"" (221 mm), Master (outer) case height: 23.2"" (589.3 mm)"

The B126-1A0-U HDMI over Cat5/Cat6 Active Extender works with a B126-002 or B126-004 transmitter (sold separately) to extend an HDMI audio/video signal to an HDMI projector, monitor or television. It's ideal for digital signs, trade shows, presentations, classrooms, churches, retail settings and other applications where the video source is located farther than conventional cables allow. A latching HDMI connector on the built-in cable provides a more secure connectionThe receiver's built-in HDMI cable connects to the display. Cat5e/6 cable connects the receiver to the B126-Series transmitter (for best results, use 24 AWG solid-wire Cat5e/6 cable, such as the N202-Series). Power is supplied by the included USB Micro-B to USB-A cable, which connects between the receiver and a USB port on the display or a USB wall charger.The B126-1A0-U can extend a 1080p (@ 60 Hz) signal up to 125 feet (38.1 meters) with full, rich stereo. Built-in RJ45 LEDs indicate the units are receiving power and a signal from the source. Built-in equalization control lets you fine-tune the image quality at the display. Easy to set up with no software or drivers to install. Works with all operating systems and HDMI sources.

The B126-1A1SR HDMI over Cat5/Cat6 Extender Kit includes a transmitter unit and a receiver unit that work in tandem to extend HDMI audio and video, RS-232 serial and IR Remote Control signals to a projector, monitor or television. The kit is ideal for digital signs, trade shows, presentations, classrooms, churches, retail settings and other applications where the video source is located farther than conventional cables allow. How far you can extend the signals depends on the cable you use to connect the transmitter and receiver. You can extend a 3840 x 2160 (4K x 2K) Ultra High Definition (UHD) signal @ 24 Hz up to 328 feet (100 m) with a single Cat6a cable, up to 230 feet (70 m) with a 24 AWG solid-wire Cat6 cable (Tripp Lite’s N202-Series), and up to 150 feet (48 m) with a 26 AWG solid-wire Cat5e cable (N001- and N002-Series).For extending computer video resolutions of 1920 x 1200 @ 60 Hz or high-definition video resolutions of 1080p @ 60 Hz up to 328 feet (100 m), use a single 24 AWG solid-wire Cat5e/6 cable, such as Tripp Lite’s N202-Series. You can also control RS-232 serial devices, such as touchscreen displays or scanners, at baud rates up to 115 Kbps. The B126-1A1SR supports 7.1-channel surround sound, DTS-HD and Dolby TrueHD audio, as well as 3D video and HDCP. Easy to set up with no software or drivers to install. Mounts to a wall, rack or pole using the included hardware.- Extends a 3840 x 2160 (4K x 2K) signal up to 328 ft. (100 m)- Supports 7.1-channel surround sound, DTS-HD and Dolby TrueHD - Controls RS-232 serial devices at baud rates up to 115 Kbps- Works with all operating systems and HDMI video sources- Plug and play—no software or drivers to install- Extends High-Definition Signals: Extends a 3840 x 2160 (4K x 2K) Ultra High Definition (UHD) signal up to: 328 ft. (100 m) with a single Cat6a cable (custom-ordered from Tripp Lite) - 230 ft. (70 m) with a 24 AWG solid-wire Cat6 cable (N202-Series) - 150 ft. (48 m) with a 26 AWG solid-wire Cat5e cable (N001- and N002-Series)- Extends a computer video signal of 1920 x 1200 @ 60 Hz or HD signal of 1080p @ 60 Hz up to 328 ft. (100 m) with Cat5e/6 patch cable (N202-Series)Supports the Latest Video and Audio Resolutions Works with all operating systems and HDMI video sources- Supports 7.1-channel surround sound, DTS-HD and Dolby TrueHD audio- Supports 3D video and HDCP- 2-way 39 KHz IR Remote Control functionality lets you control your Blu-ray player with its remote while standing at the remote monitor (and vice versa)- RS-232 serial port supports 115 Kbps full-duplex baud rates for scanners and touchscreen monitors- Plug-and-play engineering—no software or drivers to download and install - Units connect quickly to source and display with HDMI cable (P568-Series)- Included mounting hardware lets you install each unit on a wall, rack or pole

The B140-101 is a DVI over Cat5 Passive Extender kit, which comes with both transmitter and receiver units. It transmits a DVI-D Single-Link signal up to 100 feet (30.5 meters) away using a single Cat5e/6 Ethernet cable. To achieve maximum distance and resolution, use 24 AWG Solid Wire Cat5e/6 cable (N202-Series). The B140-101 is compatible with all operating systems and is plug and play with no external power, software or drivers required.Compliant with the Federal Trade Agreements Act (TAA) for GSA Schedule purchases.Installation is simple. Connect the built-in DVI connector on the transmitter unit to the source. Connect the built-in DVI connector on the receiver unit to a display. Finally, the RJ45 ports on the transmitter and receiver units are connected using a single Cat5e/6 cable. A 1920 x 1080 at 60 Hz signal can be extended up to 50 feet (15.2 meters) from the source or a 1024 x 768 at 60 Hz signal up to 100 feet.

VGA Audio + Video, Serial and IR Control Signals over Cat5/6 CablingReceives IP-based audio + video transmitted point-to-point from a source 328 ft. away Add low-cost network switches between transmitter and receiver to continue extending distance up to 328 ft. per switchCreate a Multi-In, Multi-Out Installation Using B160-Series Transmitters and ReceiversConnect up to 64 transmitters and 255 receivers through multiple dedicated managed network switchesIGMP-enabled switches allow centralized control over which sources show on which displaysDisplays video from any analog or digital source, so you can mix and match technologies and use existing sources and monitorsEnhanced Technical FeaturesSupports video resolutions up to 1920 x 1440, including 1080pUses H.264 video compression standardTransmits on 20–60 kHz IR frequencyExtends IR control signals that control a source from a remote displaySupports RS-232 serial baud rates up to 57600 BpsHDCP and 3D compatible when used with a DisplayPort or HDMI transmitter Plug-and-Play FunctionalityNo software or drivers requiredHardware included for mounting on wall, rack or poleCompatible with all B160-Series A/V over IP transmittersTAA-CompliantCompliant with the Federal Trade Agreements Act (TAA) for GSA Schedule purchases