Showing 80–90 of 205 results

The B055-001-USB-VA NetDirector® USB Server Interface Unit connects a server or computer with HD15 VGA video, 3.5 mm audio and USB mouse/keyboard ports to a compatible B064-IPG Series KVM switch. Using Cat5e/6 cabling, you can locate the KVM switch up to 164 feet (50 meters) from the server.Allowing the server to access the KVM switch’s Virtual Media functionality via low-cost Cat5e/6 cable eliminates the need for bulky KVM cables. This frees up precious space in your server cabinet, and allows for better ventilation and longer cable runs. Running cable through conduit and other tight spaces takes advantage of the increased flexibility when setting up your network application.No software or external power supply is needed. The unit’s compact, lightweight design is plug-and-play for immediate installation and deployment. It complies with the Federal Trade Agreements Act (TAA) for GSA Schedule purchases.Note: SIUs that were purchased prior to that of your KVM switch may require a firmware upgrade in order for them to work properly (see Maintenance under OSD Operation section of your B064-Series KVM Owner's Manual for details)

Distributes HDMI/DVI A/V, Serial and IR Control Signals over Cat5/6 CablingConverts audio/video to an IP-based signal that is transmitted point-to-point to a display 328 ft. awayAdd low-cost network switches between transmitter and receiver to continue extending distance up to 328 ft. per switchHDMI output for connecting a local displayCreate a Multi-In, Multi-Out Installation Using B160-Series Transmitters and ReceiversConnect up to 64 transmitters and 255 receivers through multiple dedicated managed network switchesIGMP-enabled switches allow centralized control over which sources show on which displaysVideo source can be sent to any analog or digital display, so you can mix and match technologies and use existing monitorsEnhanced Technical FeaturesSupports video resolutions up to 1920 x 1080 (1080p)Uses H.264 video compression standardTransmits on 20–60 kHz IR frequencyExtends IR control signals that control a source from a remote displaySupports RS-232 serial baud rates up to 57600 BpsHDCP and 3D compatible when used with a DisplayPort or HDMI receiverPlug-and-Play FunctionalityNo software or drivers requiredHardware included for mounting on wall, rack or poleCompatible with all B160-Series A/V over IP receiversTAA-CompliantCompliant with the Federal Trade Agreements Act (TAA) for GSA Schedule purchases

HDMI/DVI A/V, Serial and IR Control Signals over Cat5/6 CablingReceives IP-based audio/video transmitted point-to-point from a source 328 ft. away Add low-cost network switches between transmitter and receiver to continue extending distance up to 328 ft. per switchCreate a Multi-In, Multi-Out Installation Using B160-Series Transmitters and ReceiversConnect up to 64 transmitters and 255 receivers through multiple dedicated managed network switchesIGMP-enabled switches allow centralized control over which sources show on which displaysDisplays video from any analog or digital source, so you can mix and match technologies and use existing sources and monitorsEnhanced Technical FeaturesSupports video resolutions up to 1920 x 1080 (1080p) @ 60 HzUses H.264 video compression standardTransmits on 20–60 kHz IR frequencyExtends IR control signals that control a source from a remote displaySupports RS-232 serial baud rates up to 57600 BpsHDCP and 3D compatible when used with a DisplayPort or HDMI transmitter Plug-and-Play FunctionalityNo software or drivers requiredHardware included for mounting on wall, rack or poleCompatible with all B160-Series A/V over IP transmittersTAA-CompliantCompliant with the Federal Trade Agreements Act (TAA) for GSA Schedule purchases

The B160-101-HDSI HDMI over IP Gigabit LAN Ethernet Extender Kit extends and distributes HDMI or DVI audio/video, RS-232 serial and IR (infrared) remote signals from the source to the display located up to 328 feet (100 meters) away, which is more than 200 feet (61 meters) farther than a traditional Cat5e/6 solution. By adding a chain of low-cost unmanaged network switches, such as the NG5, you can continue extending the distance between source and display up to 328 feet per switch.Create a multi-in, multi-out installation with up to 64 transmitters and 255 receivers* by including dedicated managed Ethernet network switches** with Internet Group Management Protocol (IGMP), such as the NSS-G16D2. With a compatible B160-Series receiver, you can send the HDMI or DVI video source (a DVI adapter cable is included) to any analog or digital display, including VGA and DisplayPort, allowing you to mix and match technologies and use existing monitors. The IGMP-enabled switch will let you manage all connections for centralized control over which sources show on which displays.The B160-101-HDSI supports video resolutions up to 1920 x 1080 (1080p) at 60 Hz in a point-to-multipoint switch installation. It extends IR control signals that control a source, such as a media server, to a remote display, as well as RS-232 signals at serial baud rates up to 57600 Bps. The transmitter and receiver units mount to a wall, rack or pole using the including hardware.*Unmanaged switch installations are limited to two transmitter units. Number of receivers is limited to number of ports remaining on unmanaged switch.**B160-Series designed for use with dedicated network switch. Connecting to a switch used with other networking equipment will result in degraded or non-functional performance.

HDMI to VGA and Audio Converter Splits an HDMI Signal to 2 VGA Displays at the Same TimeThis six-inch adapter cable instantly connects your computer, laptop, notebook, media player, MacBook, Chromebook, Ultrabook, Blu-ray player or other device with an HDMI port to two VGA monitors or projectors simultaneously. It features a male HDMI connector and two female VGA connectors, so you can continue using your existing VGA displays and cables without the expense of new HDMI monitors.Supports High-Definition 1080p and Stereo Audio for Video PresentationsThis HDMI to VGA and audio adapter is ideal for giving video presentations in conference rooms and classrooms or playing video for digital signage in crystal-clear 1080p. It supports video resolutions up to 1920 x 1080, as well as HDCP, EDID and 3D. The HDMI audio signal passes through the adapter and splits to two 3.5 mm stereo jacks. LEDs next to each output port indicate at a glance when the adapter is transmitting a signal to the connected VGA displays.Latching HDMI Plug Provides a Secure ConnectionThe molded HDMI connector features special latches, which help prevent the adapter from becoming loose or accidentally dislodged from the source device and causing signal loss.Plug-and-Play Operation Lets You Begin Watching Video Almost ImmediatelyNo software or drivers are required. The included USB Micro-B cable powers the adapter from a USB port on your HDMI source. The lightweight unit is easy to carry in a pocket, purse, backpack or laptop bag for instant 1080p video where needed.TAA-Compliant for GSA Schedule PurchasesThe P131-06N-2VA-U is compliant with the Federal Trade Agreements Act (TAA), which makes it eligible for GSA (General Services Administration) Schedule and other federal procurement contracts.

2-port transmitter and dual receivers extend an HDMI signal via Cat5e/6/6a cable to 2 projectors, monitors or TVs up to 100 ft. away. Recommended for digital signs, classrooms, churches, offices and retail settings.- Built-in Power over Cable (PoC) technology powers the receiver- Supports high-definition video resolutions up to 1080p (@ 60 Hz)- Supports 7.1-channel surround sound audio- HDCP and 3D compliant- Plug and play—no software or drivers to installThe B126-2P2M-POC 2-Port HDMI over Cat5/Cat6 Extender Kit includes a two-port transmitter and two low-profile receivers that work in tandem to extend an HDMI audio/video signal to two projectors, monitors or televisions. The kit is recommended for digital signs, trade shows, classrooms, churches, offices, retail settings and other applications where the source is located farther than conventional cables allow. HDMI cable (see Tripp Lite’s P568-Series) connects the audio/video source, such as a Blu-ray™ player, to the transmitter’s HDMI port. Cat5e/6/6a cable connects the transmitter to the receivers’ RJ45 ports (for best results, use 24 AWG solid-wire Cat6 cable, such as Tripp Lite’s N202-Series). The receivers plug directly into the displays’ HDMI input ports. Built-in PoC technology powers the receivers over Cat5e/6/6a cable, so no external power supply on the display side is needed.The B126-2P2M-POC can extend a high-definition 1080p (at 60 Hz) signal up to 50 feet and a 1080i signal up to 100 feet. In addition to crystal-clear video, the B126-2P2M-POC delivers full, rich audio up to 7.1-channel surround sound (multi-channel or PCM) and supports 3D and HDCP standards. Easy to set up with no software or drivers to install. Transmitter mounts to a wall, rack or pole using the included hardware. Complies with the Federal Trade Agreements Act (TAA) for GSA Schedule purchases.Splits and Extends High-Definition HDMI Audio/Video Signals- 2-port transmitter extends HDMI A/V signal to 2 low-profile receivers- Recommended for digital signs, trade shows, classrooms, churches, offices, retail settings and other HDMI A/V applications- Extends a 1080p (@ 60 Hz) signal up to 50 ft. from source- Extends a 1080i signal up to 100 ft. from source- Supports 7.1-channel surround sound (multi-channel or PCM) audio- HDCP and 3D compliantEasy to Set Up and Use- Plug-and-play engineering—no software or drivers to download and install- Transmitter connects to source using HDMI cable, such as Tripp Lite’s P568-Series- Transmitter and receivers connect with Cat5e/6/6a cable (for best results, use Tripp Lite’s N202-Series)- LEDs indicate when units are receiving power or an HDMI signal- Mounting hardware included for installing transmitter on a wall, rack or poleTAA-CompliantComplies with the Federal Trade Agreements Act (TAA) for GSA Schedule purchases

The B126-110 HDMI over Cat5/Cat6 Active Remote Repeater works with Tripp Lite B126-Series transmitters and receivers to extend an HDMI signal to multiple projectors, monitors or televisions in a chain. It’s ideal for digital signs, trade shows, presentations, classrooms, churches, retail settings and other applications where the video source is located farther than conventional cables allow or that require multiple displays connected to one source. The repeater uses HDMI cable (see Tripp Lite’s P568-Series) to connect to the local monitor and Cat5e/6 cable to transmit to the receiver and/or other remote repeaters in the chain (for best results, use 24 AWG solid-wire Cat5e/6 cable, such as Tripp Lite’s N202-Series).The B126-110 can extend a 1080i (60 Hz) signal up to 53 m, a 1080p (60 Hz) signal up to 38 m and a 3D signal up to 30.5 m. You can connect up to three B126-110 units in the chain for a total of four HDMI displays and full signal extension of 213 m (1080i), 152 m (1080p) or 122 m (3D).In addition to crystal-clear video, the B126-110 delivers full, rich stereo and 7.1-channel surround sound (multi-channel or PCM) audio when used with a B126-Series transmitter. Built-in equalization control lets you fine-tune the image quality at each remote display. Supports 24-bit True Color (8 bits per channel) and HDCP compatibility. Easy to set up with no software or drivers to install. Mounts to a wall, rack or pole using the included hardware.Extends High-Definition Signals● Extends a 1080i (60 Hz) signal up to 53 m, a 1080p (60 Hz) signal up to 38 m and a 3D signal up to 30.5 m● Connect up to 3 remote repeaters to the chain for maximum signal range of 213 m (1080i), 152 m (1080p) and 122 m (3D)● Connects to next link in the chain with one Cat5e/6 cable (for best results, use 24 AWG solid-wire Cat5e/6 cable, such as Tripp Lite’s N202-Series)Supports the Latest Video and Audio Resolutions● Works with all operating systems and HDMI video sources● Supports HD resolutions up to 1080p (60 Hz)● Supports stereo and 7.1-channel surround sound (multi-channel or PCM) audio when paired with B126-002 or B126-004 transmitter unit● Supports 24-bit True Color (8 bits per channel) and HDCP● Built-in equalization control lets you adjust the image on the local monitorEasy to Set Up and Use● Plug-and-play engineering—no software or drivers to download and install● Connects quickly to local monitor with HDMI cable, such as Tripp Lite’s P568-Series● Included mounting hardware lets you install the unit on a wall, rack or pole● Extends 1080i (60 Hz) signal up to 53 m● Connect up to 3 units in a chain for maximum extension● Supports high-definition video resolutions up to 1080p (60 Hz)● Supports stereo and 7.1-channel surround sound audio● Plug and play—no software or drivers to installSystem Requirements● HDMI video source and displays● For international use, the B110-INT power supply can be purchased separately; it features plugs for the UK, Europe, and AustraliaPackage Includes● B126-110 HDMI over Cat5/Cat6 Active Remote Repeater● Screwdriver for adjusting equalization● External Power Supply with NEMA 1-15P Plug(Input: 100–240V, 50/60 Hz, 0.5A; Output: 5V, 2A)● Mounting hardware● Owner’s Manual

This 2-Port Manual VGA/SVGA Switch is the optimal solution for connecting two computers to one monitor or two monitors to one computer. The 2-Port Manual VGA/SVGA Switch features a fully shielded rugged metal case with front-panel push-button switching. Interior printed circuit board design allows for crystal clear resolutions up to 1600 x 1280. It does not require any AC power to operate.

HDMI Extender Receiver Ideal for Digital Signage in Schools and WorkplacesThis 4K receiver is recommended for video presentations in conference rooms, schools, trade shows, meeting facilities, houses of worship, retail settings, hotels and other digital signage applications where the source and display are farther apart than conventional A/V cables allow.Extends a 4K A/V Transmission up to 230 ft....or Even FartherThe B127A-1A0-FH connects to a B127A-Series transmitter, switch or splitter to extend 4K signals from an HDMI source to an HDMI display up to 230 feet (70.1 meters) away via user-supplied Cat6 cabling. By adding a B127A-010-H signal repeater (sold separately) to the application, you can extend the signal up to 400 feet (121.9 meters).Supports Crystal-Clear 4K Video with Multi-Channel Audio, HDR and 4:4:4 ColorThe B127A-1A0-FH supports Ultra HD resolutions up to 3840 x 2160 (4K x 2K) at 60 Hz with 7.1-channel surround sound audio. High Dynamic Range (HDR) provides a wide range of vibrant colors with richer contrast, brighter whites and deeper blacks that pop on your 4K display. HDCP 2.2 compliance allows you to stream 4K Amazon and Netflix content with no complications. This receiver also supports 4:4:4 chroma subsampling for top-level PC gaming or using your HDTV as a PC monitor. Built-in equalization allows you to fine-tune the image quality at the remote display.Built-In PoC Technology Provides Receiver Power to Avoid Bulky External Power BricksPower over Cable (PoC) technology powers the B127A-1A0-FH over Cat6 cable. An LED indicates when the receiver and transmitter are connected. PoC lets you avoid the hassle of a bulky power brick and gives you the freedom to place the receiver where needed without worrying about finding a nearby AC outlet.Plug-and-Play Operation for Quick Setup and Immediate UseThe single-gang metal wall-plate receiver works right out of the package with no software required and all mounting screws included. Connect the receiver to a transmitter, switch or splitter with user-supplied Cat6 cable (such as N202-Series). Connect to a 4K display with a user-supplied HDMI cable (such as P568- or P569-Series).TAA-Compliant for GSA Schedule PurchasesThe B127A-1A0-FH is compliant with the Federal Trade Agreements Act (TAA), which makes it eligible for GSA (General Services Administration) Schedule and other federal procurement contracts.

HDMI Quad-Output Extender Kit Ideal for Digital Signage in Schools and WorkplacesThis 4K splitter/receivers combo is recommended for video presentations in conference rooms, schools, trade shows, meeting facilities, houses of worship, retail settings, hotels and other digital signage applications where the source and display are farther apart than conventional A/V cables allow.Extends a 4K A/V Transmission up to 230 ft....or Even FartherThe included splitter connects to three included pigtail receivers (plus one more optional B127A-Series receiver, sold separately) to extend 4K signals from an HDMI source to four HDMI displays up to 230 feet (70.1 meters) away via user-supplied Cat6 cabling. By adding B127A-010-H signal repeaters (sold separately) to the application, you can extend the signal to each connected display up to 400 feet (121.9 meters).Transmits Crystal-Clear 4K Video with Multi-Channel Audio, HDR and 4:4:4 ColorThe B127A-004-BHPH3 supports Ultra HD resolutions up to 3840 x 2160 (4K x 2K) at 60 Hz with true uncompressed 7.1-channel digital audio and Dolby TrueHD. High Dynamic Range (HDR) provides a wide range of vibrant colors with richer contrast, brighter whites and deeper blacks that pop on your 4K display. HDCP 2.2 compliance allows you to stream 4K Amazon and Netflix content with no complications. Advanced 4:4:4 chroma subsampling is ideal for top-level PC gaming or using your HDTV as a PC monitor.Multi-Resolution Support Allows Mixing and Matching of Displays of Different ResolutionsSay you have a brand new 4K/60 Hz HDTV in one room, but want to also connect your Blu-ray player or satellite box to an older 1080p TV in another room. The B127A-004-BHPH3 is backward compatible with 4K/30 Hz and 1080p resolutions via automatic switching, allowing each connected monitor to display video at its maximum resolution.Local HDMI Port on Transmitter Supports 4K @ 60 Hz ResolutionTo monitor the video signal being extended to the receivers, connect a 4K display to the splitter’s local HDMI port with the included HDMI cable. This port does not support multi-resolution capabilities, so the connected monitor must also support 4K/60 Hz to function properly.Built-In PoC Technology Provides Receiver Power to Avoid Bulky External Power BricksPower over Cable (PoC) technology powers the connected receivers over Cat6 cable. LEDs indicate when the system is receiving power and a signal is being transmitted. PoC lets you avoid the hassle of a bulky power brick and gives you the freedom to place the receivers where needed without worrying about finding a nearby AC outlet.Plug-and-Play Operation for Quick Setup and Immediate UseThe splitter and receivers work right out of the package with no software required. Mounting hardware is included for installing the splitter on a wall, pole or 19-inch rack. Connect the splitter to an HDMI source device with a user-supplied HDMI cable (such as P568- or P569-Series). The receivers’ pigtail HDMI connectors plug directly into a 4K display.TAA-Compliant for GSA Schedule PurchasesThe B127A-004-BHPH3 is compliant with the Federal Trade Agreements Act (TAA), which makes it eligible for GSA (General Services Administration) Schedule and other federal procurement contracts.